web space | free hosting | Business Web Hosting | Free Website Submission | shopping cart | php hosting

Minimum tool-set:

Additional or optional items:

Glues

Building boards

Scoring

Cutting

Touching up cut edges

Ventilators

Windows

Gun barrels

Bollards

Flags

Masts

Ships boats

Photo-etch metal parts

Ladders and companionways

Railings

Rigging

Awnings

Hints and tips for boat/ship model builders.

Tools

Minimum tool-set:

  1. Scalpel or sharp pointed knife, either disposable blades or re-sharpenable.
  2. Pointed but BLUNT implement for scoring, eg compass point, old biro, blunt knife blade.
  3. Steel ruler (cork-backed if possible, both 15cm and 30cm are recommended).
  4. Tweezers for handling small parts (smooth jaws if possible).
  5. Glue
  6. Paints, coloured pencils or watercolour markers for touching up cut edges
  7. Self-healing cutting mat.
  • Additional or optional items:
    1. Hole punch in a variety of sizes.
    2. Toothpicks for applying small amounts of glue.
    3. Variety of clothes pegs or clamps for clamping parts while they glue.
    4. Variety of small rods or tubes for rolling cylinders.
    5. Large craft knife for roughly cutting out parts.
    6. Sharp scissors with pointed tips.
    7. Small set squares for checking right angles.
    8. Sticky tape for holding parts in place while they dry
    9. Spare card for laminating parts and re-inforcing joins, etc.
  • Glues
  • Three main types of glue can be used.

    1. Petroleum based glues - UHU All purpose/Alleskleber. These generally dry clear and can be used for all parts. Care is needed as they can string and also be difficult to just get the small amount required on the part.
    2. PVA (Poly Vinyl Acrylate) based glue - also called White glue, wood glue, school glue - Bostik Resin W, Tacky Glue, Elmers - it is Very good for gluing paper, it's cheap, it dries nearly matt, it can easily be placed with a toothpick. Thinned with water it can be used to size absorbent card. Do not over-apply these glues or they will buckle card.
    3. Cyano-acrylate glues - supergue, CA glue, instant glue - available in differing setting times and consistencies, relatively expensive. The thin/fast glues are good for stiffening thin parts like flagpoles as they soak in and leave the part almost plastic-like, but they darken colours.
  • Building boards
  • A completely flat, stiff and adequately sized building board is vital if your model is to be assembled correctly. Gluing the base plate to a stiff, flat surface will mean that the hull does not warp or twist during assembly.

    Cardboard, plastic or wood can be used, the only criteria being the building board must be sufficiently thick that it will not warp and it must be long and wide enough for the whole model to fit.

    The model should be glued to the building board with a series of small dots around the periphery and a number of small dots beneath any structural members, eg the hull spine. When complete, the model can be separated from the building board by slipping a thin flat knife or razor blade between the model and the building board and working it carefully back and forth.

    Some plastics have the added advantage that certain glues will not stick to them permanently. I use a thin (3mm) sheet of plastic sheet of the type sold for glazing or picture framing (acrylic or methyl acrylate plastic) glued to a sheet of MDF (medium density fibreboard) with PVA adhesive. The model is also glued in place with PVA. This glue holds fast during assembly, but separates cleanly when required without tearing (the model just sort of "pops" off the plastic).

    Scoring

    Score any fold lines before cutting out a part. Use a blunt pointed instrument and a ruler to score fold lines. Note some parts are designed to be scored on the reverse - check the symbols used to indicate the score lines. Some people prefer to make a cut through half the thickness of the card with a sharp knife, personally I donít do this.

    Cutting

    Cut out parts on a self-healing cutting mat (available from hobby or craft shops), a thick pile of newspaper or cardboard. I strongly recommend a self-healing cutting mat. They are not expensive and will last a long time.

    Do not cut out any parts until they are required. Cut out any openings in a part before cutting out the part.

    Use a sharp knife or a scalpel for straight cuts and always use a straight edge. A cork-backed steel rule will not mark the model sheets. Small sharp scissors can be used for curved parts.

    A set of steel french curves are useful for cutting out curved parts - use plastic ones if you feel brave.

    When cutting into corners, for example a window opening, start with you knife point in the corner and cut outwards. Make two cuts that meet in the middle if necessary.

    Watch out for your fingers, craft knives and scalpels are sharp.

    The sticky area on the back of a Post-ItTM is useful for holding small parts while cutting.

    Test fit all parts before glueing.

    Touching up cut edges

    The appearance of a model can be greatly enhanced by colouring the cut edges (which would show white) the same colour as the printing on the card.

    Watercolour paints, coloured pencils, felt-tip pens, watercolour pencils, watercolour paint felt-tip pens or pastels can all be used. Try on a piece of scrap card from the model first. I almost exclusively use watercolour markers - Do NOT use normal felt-tips as they bleed into the card from the edge very badly.

    It only seems to be important to get the tone right, the precise colour match is not so important - a set of various grey coloured markers in various tones works for me in most cases.

    Ventilators

    The cowl on top of ventilators should be gently burnished with a rounded implement to achieve the true rounded (near hemispherical) shape.

    Windows

    The "glass" in the windows of chart houses, bridges and deck houses can be carefully cut out and replaced with a clear glazing material (Overhead projector transparency sheets seem a good compromise between transparency and stiffness). The interior can be scratch-built if not supplied.

    The "glass" in deck skylights may be replaced with small pieces of clear glazing material. Colour the underlying deck black.

    Gun barrels

    Paper gun barrels can be replaced with lengths of plastic or metal tubing (rod for the smaller barrels). These can be wrapped in the paper parts or painted to match. Alternatively scanning and printing the parts onto very thin paper makes it easier to roll.

    Bollards

    Small scale bollards can be quickly made from plastic rod, painted an appropriate colour and cut into short lengths. Glue in place with instant glue.

    Flags

    Flags should be scanned and printed onto VERY thin paper. They should then be cut out, folded and glued double with PVA glue. This glue soaks into the paper and softens it. Before the glue dries, use a pair of tweezers to fold and realistically drape the flag. Glue in place on the flagpole or mast when dry.

    Masts

    Scanning the mast parts and printing out onto thin paper will make rolling up mast parts easier.

    Paper masts can be replaced with masts made from wood, plastic rod (or tubing) or metal wire. Short lengths of dried grass can also be used, though I have not tried this myself.

    Rolling paper masts around a length of wire will provide stiffness and the ability to straighten the mast if needed.

    Wooden or plastic masts can be mounted in the chuck of an electric drill and sanded to a tapering shape.

    Wooden or plastic masts can be easily coloured black or dark brown by using a permanent marker. For lighter colours, modellers paint must be used.

    Ships boats

    The appearance of ships boats can be greatly improved by forming the hulls into the correct rounded shape. Use a small rounded implement (the ball on the end of my craft knife is ideal).

    Place the boat sides printed side down on a surface with some give (an upside down foam-backed mouse mat seems to work well) and gradually burnish a curve into the part by using a rotating action while gradually increasing the pressure. Try this out on some scrap card first.

    Photo-etch metal parts

    Photo-etched metal parts are made of metal and the etching process eats away the unwanted metal without the stress associated with cutting or stamping. This is ideal for model parts and very fine and delicate parts can be produced and used to replace detailed or hard to cut out parts. Other parts can be produced that would not be possible with card.

    The disadvantages are that the parts are expensive, at least doubling the total cost of a model and the model cannot be said to be truly "card".

    Generic parts are available - ladders, hand-wheels, anchor chain, railings, etc - as well as complete sets for specific models from some suppliers.

    Ladders and companionways

    Ladders and companionways can be replaced with scratch-built alternatives that have proper steps - use the original as a template. A notched piece of card can act as a template.

    Replace any printed handrails with wire or plastic shaped to fit. Parts should be de-greased, primed, painted, bent to shape if required and glued in place with CA/instant glue.

    Railings

    A lot of ship models have railings printed as part of the hull sides or supplied separately. These are acceptable and can be fitted if desired. However, proper scale railings can dramatically improve the appearance of a ship model and are not difficult to make and fit.

    Railings - option 1

    There are photo-etched metal railings (available from good hobby suppliers or by mail order) suitable for use with paper ship models. Cut the railings to length, bend to shape, paint an appropriate colour and glue into place.

    Railings - option 2

    Very detailed railings can be made using lengths of wire for the stanchions (supports) and lengths of thread. Make a hole in the deck for each stanchion if the positions are marked, otherwise you will need to identify the correct spacing. Then cut a length of wire (using the supplied paper rails as a template) and glue into the hole in the deck using instant glue (also known as superglue, CA or cyanoacrylate). Use white glue to fix thread between the stanchions and paint an appropriate colour.

    Note that holes for the railings should be made in any unsupported decks such as bridge wings before they are glued in place.

    Railings - option 3

    Similar to option 2 but paper strips are used for stanchions folded over thread "rails" and glued into place. Use any supplied paper railings as a template.

    Railings - option 4

    Realistic railings can be made from thread stiffened with glue. These can be purchased (from mail order suppliers) in standard lengths or can be very easily made by the modeller.

    The basic method is to wrap thread round an open frame to form a criss-crossed grid of threads, soak the threads in glue and allow to set, then cut out and fix into place. This method also produces accurate scale ladders.

    Full instructions and a template for some standard railing profiles are given below.

    Rigging

    Fine thread, nylon monofilament or stretched sprue can be use for rigging.

    Fine nylon monofilament is available from fishing tackle suppliers. It can be coloured black with a permanent marker by unreeling a length, placing the tip of the marker on the thread (on a scrap piece of paper) near the reel, then pulling the thread through the tip of the marker. If the monofilament does not lie straight, place a length in boiling water briefly then hang up with a weight tied to the end. Cut to length and glue in place with instant glue (also known as superglue, CA or cyanoacrylate).

    It is often easier to make any holes for fastening rigging in decks, etc before cutting out and gluing the deck in place. Standing rigging lines are often better glued into the deck before assembly, then tied to the top of the mast at a later stage.

    With small models it is possible to pass the thread right through the model. This allows the modeller to tie the thread to the mast, tension and glue the other end to the bottom of the model, out of sight.

    Block and tackles

    Realistic block and tackle may be made by cutting out small paper disks - one for each side of the blocks - and then sandwiching a number of lengths of thread or monofilament between the halves of the paper "blocks". Lifeboat davits and other derricks may be replaced with plastic rod or soft wire bent to shape.

    Awnings

    Steam-era ships often had awnings (canvas sunshades) on exposed decks and the awning poles and supporting wires were a reasonably conspicuous feature. The poles can be easily made (if not supplied) from stiffened paper, wire or thin plastic rod. They should be rigged with fine thread, nylon monofilament or stretched plastic sprue. Awnings may be made from very thin ivory or cream coloured paper or white paper coloured with watercolour paint (the paper for rolling your own cigarrettes is thin and strong). A couple of photographs of the subject will show where the poles should be mounted (if not already marked on the model decks) and the shape of the awnings.

    Lighting

    Small electric light bulbs and a battery can be added inside a model to illuminate the (carefully cut-out) windows. Some experimentation may be needed as thin card is translucent and may need lining with foil to prevent a luminous glow from the whole model.

    Dioramas and bases

    Display base

    A display base can be made from an appropriate piece of wood. Sand and varnish the sides. Cover the top with a suitable piece of green-blue paper, glue your model ship in place and coat the paper with artists gel medium. Build up several layers and try and replicate some waves. White paint sparingly applied can pick out the wake. Practice without gluing the model in place first!

    For the really adventurous, add a wharf, some dock-side buildings and accessories, small boats and figures. A wisp of cotton wool from the funnel of a steamer looks convincing - your imagination is the only limit.

    Display cases

    To prevent dust settling on your completed model (or during assembly) it is a good idea to invest in a good display case for your models or make one yourself. A simple wooden framework can be glazed with plastic or glass (most glass merchants will cut to size for a small charge). An even simpler case can be made by glueing plastic sheet together at the edges.

    David Hathaway/Paper Shipwright